
Hydraulic Power Pack for Rubber Processing Machine: Sheet and Coated Fabric
A hydraulic power pack for rubber processing machine guiding provides the oil pressure that shifts heavy roll stands, so that rubber sheet and coated fabric run and wind up on a true line. Krishna Engineering Works builds the power pack in Ahmedabad, with web aligner units suited to the high loads, heat and dust of rubber plants.
Where is a power pack used on rubber processing machines?
A power pack is used wherever a rubber line unwinds or winds a continuous web: at fabric let-offs, at wind-up stations and at the entry of cutting and slitting machines. The cylinder it feeds moves the stand that carries the roll.
Rubber plants process two kinds of web. One is fabric that is to be coated or impregnated with rubber. The other is the rubber product itself: sheet from a calender, coated fabric, and belting. The first behaves like any heavy textile. The second is tacky, heavy and easily deformed, and it sets the rules for the whole guiding arrangement.
| Machine section | Web | What the guide does | What the cylinder moves |
| Fabric let-off ahead of a calender or coating head | Dry fabric | Centres the fabric so rubber covers it evenly from edge to edge | Let-off stand |
| Wind-up after a calender | Uncured sheet or coated fabric, with liner | Lays rubber and liner together in a level roll | Wind-up stand |
| Liner let-off at the wind-up | Liner cloth or film | Keeps the liner covering the full width of the rubber | Liner stand |
| Entry of a slitter or bias cutter | Coated fabric from a roll | Presents the edge square to the knives | Let-off stand |
| Sheeting and belting lines | Thick sheet or belt | Keeps the product central on the line | Wind-up stand |
How do tacky webs change the guiding method?
Tacky webs are guided by moving the roll, not by steering the web. Uncured rubber sticks to whatever it touches and stretches under very little force, so the usual steering frame with idler rollers is rarely the right tool for it.
Three rules follow from the nature of the material.
- Guide the fabric before the rubber goes on. Dry fabric can be handled like any web. If it enters the calender or coating head on line, the coated product leaves on line, and far less correction is needed afterwards.
- Guide the stand at the wind-up. At the wind-up the sensor travels with the stand, and the cylinder moves the whole roll to meet the sheet. The sheet itself is not bent, twisted or dragged sideways.
- Keep contact to a minimum. Every roller that a tacky sheet wraps is a place where it can stick, stretch or pick up marks. A guide that needs no extra rollers in the web path is the one to prefer.
Where a pivoting frame is used on fabric ahead of the process, it is the tracking roller assembly, built with centre pivot or end pivot guiding. The different guiding positions are compared on the web guiding system page.
The liner deserves its own attention. A liner that runs off to one side leaves a strip of bare rubber, and that strip bonds to the next lap in the roll. Guiding of the liner on its own machine is covered on the page for the power pack on a liner rewinder machine.
Choosing a hydraulic power pack for rubber processing machine loads
Choose the model by the force needed to move the heaviest full roll, with a clear margin. Rubber is dense, rolls are wound on steel shells, and the stands that carry them are built heavily, so the moving mass is well above that of a film or paper machine of the same width.
The published figures for the two standard models are below. Force is quoted for a cylinder of 50.8 mm diameter.
| Item | KEW-17 | KEW-30 |
| Motor rating (3 phase, 50 Hz) | 0.5 HP | 1 HP |
| Line pressure | 14 bar | 21 bar |
| Maximum operating force | 260 kg | 389.5 kg |
| Pump flow rate | 3.4 l/min | 5.8 l/min |
| Follow-up speed | 30 mm/sec | 40 mm/sec |
| Tank capacity | 17 litres | 30 litres |
| Weight including oil | 40 kg | 60 kg |
The cylinder does not lift the roll. It only has to overcome the rolling or sliding resistance of the stand, which is a fraction of the weight when the stand runs on wheels or linear bearings in good order. The fraction rises steeply when rails are dry, bent or packed with rubber crumb and powder.
For a fabric let-off the smaller model is often sufficient. For wind-up stands carrying full rolls of sheet or coated fabric, start from the larger model and check the margin. Krishna Engineering Works offers power pack units in different models from 0.25 HP to 3 HP, so state the true load and a suitable unit can be proposed. How pressure and flow are produced inside the unit is explained on the hydraulic power pack page.
Why does a rubber line need a robust cylinder installation?
A rubber line needs a robust installation because the cylinder works at high load, in a dirty area, for long shifts. The hydraulic cylinder is a simple component, but the way it is mounted decides how long its seals and rod last.
- Push in a straight line. The cylinder must be in line with the travel of the stand. Any angle puts a side load on the rod and wears the seal and bush on one side.
- Use free pins at both ends. Pin joints let the cylinder follow small errors in the rails. A cylinder bolted rigidly at both ends fights the stand at every stroke.
- Make the brackets stiff. A bracket that flexes under load gives the guide lost motion. The stand then hunts, because the first part of each correction only bends steel.
- Stay inside the stroke. The cylinder supplied with the web aligner unit has a 6 inch stroke. Centre the stand at the start of each roll, so that the piston never reaches the end of its travel during normal correction.
- Protect the rod. Powder and rubber crumb on an exposed rod are carried into the seal. As general practice the rod is kept wiped and shielded from falling debris.
Pressure in the circuit is limited by a relief valve, which opens when the cylinder meets more resistance than the unit is set for. If the guide stalls against a jammed stand, the relief valve protects the pump, but the oil heats up while it is passing. A stand that stalls regularly needs its rails seen to.
Which sensor suits rubber sheet and coated fabric?
Both sensing methods work on rubber products, because the material is solid and opaque. The choice depends on the edge and the surroundings.
| Web | Edge condition | Suitable sensing | Note |
| Dry fabric before coating | Selvedge, sometimes hairy | Air sensor | Open weaves weaken the air signal, so name the fabric |
| Calendered rubber sheet | Thick, soft, sometimes wavy | Air sensor or photocell | Keep the sensor clear of contact with the tacky edge |
| Rubber coated fabric | Firm, may carry rubber flash | Air sensor or photocell | Trimmed edges guide better than untrimmed ones |
| Liner cloth or film | Thin, may be creased | Air sensor | Mount close after a roller where the liner is flat |
The hydro-pneumatic web aligner unit reads the edge with a low pressure air jet, adjustable from 5 to 28 mbar. Air flows out of the sensor at all times, which helps to keep anti-tack powder and carbon black out of the gap. Its kit includes a 0.5 HP motor, 5 metres each of air pipe and oil pipe, one sensor, one adjuster, one air filter, one oil filter and one hydraulic cylinder, as itemised on the web aligner unit page.
The electro-hydro web aligner (power pack) unit uses a photocell sensor for the edge, with an AC motor, an electrical panel board to operate the complete unit, a hydraulic cylinder, an adjuster and an oil pipe. Black rubber interrupts a light beam completely, so the photocell gives a clear signal, provided the lens is kept free of powder.
Whichever sensor is used, set the gap wide enough that a thick or wavy edge never touches the sensor arms. Uncured rubber that touches the sensor will stick to it.
Heat, powder and carbon black: looking after the oil
Look after the oil by keeping it cool and keeping it closed. Rubber plants are warm, and calenders, mills and curing equipment add heat to the area around them.
Warm oil is thin oil. It leaks more readily past the internal clearances of the valve and cylinder, so the guide holds less firmly and the pump has to work harder for the same result. Stand the power pack clear of calender rolls and steam lines, and use the length of the oil pipes to place the tank in moving air. Keep hoses away from hot surfaces.
Contamination is the other risk. Carbon black and anti-tack powder are fine enough to pass a carelessly opened filler and abrasive enough to damage a servo valve. The routine below is general practice for dusty plants.
- Wipe the filler cap and the top of the tank before opening it.
- Top up only with the recommended oil (Servo 32, Enklo 44 or Hydro 37) from a clean, closed container.
- Check the oil filter on a fixed schedule and at any sign of slow response.
- Clean or replace the air filter of the sensor at the same time.
- Change the oil and the filter element when the oil darkens, clouds or feels gritty between the fingers.
- Clean the rails of the stand and remove rubber crumb at every roll change.
Starting the guide on a new roll
Start each roll with the stand centred and the guide in manual. With a tacky web the first laps decide the shape of the whole roll, because a lap that has stuck in the wrong place cannot be slid across.
Thread the liner and the sheet, bring the stand to the centre of its travel, and set the sensor to the edge by eye. Switch to automatic as soon as the sheet is running under tension. If the guide is left in automatic with no web in the sensor, the stand will run to the end of the stroke and the first laps will be laid off centre.
Related products and service
Rubber covered rollers are part of the same machinery. Krishna Engineering Works also mentions rubber rollers for tracking roller assemblies, and the client’s rubber rollers site covers that product. Heavy fabric rolls of a similar kind are met on paper and board lines, described under the power pack for a paper machine.
Units of Indian and imported makes that have lost their response can be sent for repairs and servicing. Spares for the power pack and the hydro-pneumatic web aligner unit are kept readily available, and the company has the capacity to supply 100 to 150 units per month. Other machines are listed under power packs by machine.
What to send for a quotation
Send the information below, so that the force and the sensing method can be matched to the line.
- Type of rubber processing machine and the section to be guided
- Web: dry fabric, uncured sheet, coated fabric, belting or liner
- Web width range and thickness range
- Line speed
- Weight of the heaviest full roll with its shell
- How the stand is carried, and the travel available on each side of centre
- Temperature near the stand, and the dust or powder present
- Whether an electrical panel or an all air sensing arrangement is preferred
- Make and model of any existing guiding unit
Send the enquiry through the contact page, or see the complete range on the hydraulic power pack products page.
Frequently Asked Questions
Can uncured rubber sheet be guided with a steering roller frame?
It is not the preferred method. Uncured rubber sheet is tacky and stretches under small forces, so wrapping it around extra idler rollers and twisting it sideways risks sticking, marking and distortion. The usual approach is to guide the fabric before coating and to move the wind-up stand to meet the sheet.
How much force is needed to move a heavy rubber roll stand?
The force needed is the rolling or sliding resistance of the stand, not the weight of the roll. On wheels or linear bearings in good condition it is a small fraction of the moving weight. On dry or dirty slides it can be many times higher. Send the roll weight and stand design with your enquiry.
Which sensor works on black rubber sheet?
Both an air sensor and a photocell sensor work on black rubber sheet, because the material is solid and fully opaque. The air sensor has the advantage of blowing powder away from its own ports. The photocell gives a strong signal but needs its lens wiped regularly in a dusty area.
Why should fabric be guided before it enters the rubber calender?
Fabric should be guided before the calender because it is the last point at which the web is dry and easy to move. If the fabric enters centrally, rubber covers it evenly from edge to edge and the coated product leaves on line. Errors made here cannot be corrected well afterwards.
Does carbon black damage a hydraulic power pack?
Carbon black damages a power pack only if it gets into the oil. The particles are fine and abrasive, and they wear the close fitting parts of the servo valve and pump. Keep the filler closed, wipe around it before topping up, use a clean container and check the oil filter on a regular schedule.
What happens if the wind-up stand jams while the guide is correcting?
If the stand jams, pressure in the cylinder rises until the relief valve opens and passes the pump flow back to the tank. This protects the pump and pipes, but the oil warms while it does so. Free the stand promptly, find the cause of the jam, and clean the rails before restarting.
