
Hydraulic Power Pack for Coating Machine: Guiding at the Coating Head and After the Dryer
A hydraulic power pack for coating machine guiding drives the cylinders that hold the web in one sideways position under the coating head and bring it back on line after the dryer. Krishna Engineering Works builds the power pack and the web aligner units around it in Ahmedabad, for coating lines that run film, paper, foil and fabric.
Where is guiding needed on a coating line?
Guiding is needed at three points on a coating line: at the unwind, at the exit of the dryer and at the rewind. Each point protects a different part of the process.
| Guide position | What it protects | What the cylinder moves | Typical load |
| Unwind | Position of the web under the coating head | Unwind stand and reel | High, falls as the reel empties |
| Dryer exit | Web path into the chill rollers, laminator or rewind | Pivoting roller frame | Low |
| Rewind | Shape of the finished coated reel | Rewind stand and reel | High, rises as the reel builds |
Short lines with a small dryer often manage with the unwind guide alone. Lines with a long dryer need the second guide, because a web that was perfectly placed at the coating head has many metres of hot, unsupported travel in which to wander again.
Why does web position matter at the coating head?
Web position matters at the coating head because the coating is laid down at a fixed place on the machine, not at a fixed place on the web. If the web moves sideways, the coated band moves across it.
The practical results are easy to recognise on any coating line.
- Uneven margins. Most coated products need a bare margin of set width on one or both edges. A wandering web gives a wide margin on one side and a narrow one on the other.
- Coating on the backing roller. When the web moves off the coated width, the uncovered part of the roller picks up coating. It then transfers to the back of the web or builds up as a hard ring.
- Waste at the slitter. Coated width that is off centre must be trimmed away later, and the trim carries expensive coating with it.
- Edge faults in drying. A thick wet edge dries more slowly than the rest and can block in the rewound reel.
The unwind guide deals with all four. The cylinder shifts the unwind stand, the sensor on the fixed frame reads the edge after the first idler, and the web arrives at the coating head on a constant line. On gravure, reverse roll and knife type heads alike, the guide should be the last thing that changes the web path before the head.
Guiding after the dryer
Guide at the dryer exit when the web has drifted inside the dryer, which is common on long machines. Inside a dryer the web runs over many idler rollers or floats on air, its temperature rises, its tension falls and the moisture or solvent content changes across the width. Each of those can push it sideways.
Neither end of the web can be moved at this point, so the correction is made by steering. A tracking roller assembly carries two idler rollers on a frame that pivots under the action of the cylinder, and the web is turned back onto its line as it passes over them. The load on the cylinder is small, since only the frame and its rollers move.
Two points decide whether a dryer exit guide works well.
- Free span. The web needs a clear run into the frame and a clear run out of it, so it can twist without creasing. A coated web just out of the dryer is warm and soft, so allow generous spans.
- Sensor position. The sensor goes close after the exit roller of the frame, on the fixed structure, and outside the direct blast of the dryer exhaust.
Where there is no room for a steering frame, the rewind is guided instead. The sensor travels with the rewind stand and the stand follows the web, so the coated reel still builds with flat sides. The three arrangements are compared on the web guiding system page.
How does dryer heat affect the power pack?
Dryer heat thins the oil, and thin oil makes the guide slower and softer. The power pack is a small tank of oil with a motor on top. It gets rid of its own heat through the tank walls, and it can only do that if the air around it is cooler than the oil.
Mineral hydraulic oil loses viscosity quickly as it warms. Thinner oil slips more easily past the clearances inside the pump, the valve and the cylinder seals, so less of the pump flow reaches the cylinder and the stand creeps more readily under load. Hot oil also ages faster, darkens and leaves varnish on the valve spool.
As general practice, a small power pack runs happily when the tank is comfortably warm to the hand and becomes a concern when it is too hot to keep a hand on. The table links what the operator notices to the likely oil condition.
| What is noticed | Likely oil condition | What to do |
| Guide sluggish for the first minutes of a shift | Oil cold and thick | Run the pack a little before threading the web |
| Guide lively in the morning, lazy by afternoon | Oil overheating near the dryer | Move or shield the pack, improve air flow around the tank |
| Stand drifts slowly when the line stops | Thin oil leaking past valve or seals | Check oil temperature first, then have the unit serviced |
| Oil dark with a burnt smell | Oil oxidised by long hot running | Change oil and filter element, find the heat source |
| Level in the tank rises and falls through the day | Normal expansion, or air drawn in | Check suction joints and the level when cold |
The cures are simple and mostly a matter of placement.
- Stand the power pack at the unwind end or at the operator side, away from the dryer body, burners, steam pipes and hot air ducts.
- Use the pipe length to gain distance. The unit is supplied with 5 metres of oil pipe and 5 metres of air pipe, which is usually enough to keep the tank in cool air.
- Leave space on all sides of the tank and do not box it in under a platform.
- Keep oil pipes off hot surfaces, and do not run them along the dryer wall.
- A larger tank carries more oil and has more wall area to cool it. The KEW-30 holds 30 litres against 17 litres in the KEW-17.
Sensor choice in coating areas
Choose air sensing where solvent vapour, dust or clear film is present, and photocell sensing where the web is opaque and an electrical unit is preferred. The hydro-pneumo web aligner reads the edge with a low pressure air jet, adjustable from 5 to 28 mbar, so the sensor head and its pipe carry no electrical signal. That is useful beside a solvent coating head.
The electro-hydro web aligner unit has a photocell sensor for the edge, an AC motor, an electrical panel board to operate the complete unit, a hydraulic cylinder, an adjuster and an oil pipe. In either case the motor of the power pack is electrical, so its position must follow the plant’s rules for the coating area. Give the area classification when you enquire.
At the dryer exit, remember that moving air disturbs an air jet. Shield the fork or place it where the exhaust does not blow across it.
Selecting the unit for a coating machine
Select the unit guide by guide, starting with the load. The steps below give a workable order.
- List the guides: unwind, dryer exit, rewind.
- For each stand guide, note the heaviest reel and how the stand is carried. Friction of the stand, not weight alone, sets the push needed.
- Compare that push with the maximum operating force on the published 50.8 mm cylinder: 260 kg for the KEW-17 at 14 bar and 389.5 kg for the KEW-30 at 21 bar.
- Check correction speed against line speed. The two models give 30 mm/sec and 40 mm/sec follow-up speed.
- Decide whether the guides share a tank. Double and triple power units have two and three servo valves on the same reservoir.
- Choose the sensing method for each position.
- Mark where each power pack can stand in cool, clean air.
The hydro-pneumatic web aligner unit comes complete with a 0.5 HP motor, pipes, sensor, adjuster, air filter, oil filter and a hydraulic cylinder of 6 inch stroke, as itemised on the web aligner unit page. The pack itself is explained on the hydraulic power pack page, and other models are available from 0.25 HP to 3 HP.
Keeping coating out of the hydraulics
Keep coating compound, adhesive and solvent away from the tank, the cylinder rod and the sensor. Coating lines are sticky places, and a film of dried coating does more harm than dust.
- Wipe the cylinder rod when the line is cleaned. Dried coating on the rod is dragged through the rod seal and scores it.
- Keep the filler cap closed during wash up, and never top up from an open can that has stood near the coating station.
- Clean the sensor ports with a dry cloth. Solvent on a rag is acceptable for the metal parts, but do not flood the air pipe.
- Check the air filter element more often on solvent lines, because vapour softens deposits that then clog the element.
- Use Servo 32, Enklo 44 or Hydro 37 oil, and do not mix grades when topping up.
A guide that has become unreliable after years beside a coating head can be sent for repairs and servicing, where worn parts are replaced with new ones. Spares are kept readily available.
Coating lines in the wider range
Coating often shares a line with lamination, where a second web joins at a nip and both must be guided, as described on the page for the power pack on a lamination machine. Krishna Engineering Works also manufactures the coating machine itself. All machine applications are listed under power packs by machine.
What to send for a coating machine guiding quotation
Send a sketch of the web path with the details below.
- Coating method and whether the coating is solvent based, water based or hot melt
- Web materials, width range and line speed
- Coated width and the margin to be held at each edge
- Dryer length and type, and the web temperature at the dryer exit
- Heaviest reel at unwind and rewind, and how each stand is carried
- Guide positions required, and the free web span available at the dryer exit
- Area classification near each sensor and each power pack
- Distance from each guide to a cool position for the power pack
Send the enquiry through the contact page.
Frequently Asked Questions
Why does a coating machine need web guiding before the coating head?
A coating machine needs guiding before the head because the coating is applied at a fixed position on the machine. If the web wanders, the coated band shifts across it, the margins become uneven and coating reaches the backing roller. An unwind guide places the web on a constant line just before it is coated.
Is a second guide needed after the dryer of a coating line?
A second guide is needed when the dryer is long enough for the web to drift again. Heat, falling tension and many rollers all move the web sideways inside the dryer. A steering frame at the exit, or a guided rewind, brings the web back on line so the coated reel winds with flat sides.
How hot can the oil in a web guide power pack run on a coating line?
Oil should stay warm, not hot. As general practice, a tank that is comfortable to touch is fine, and a tank too hot to hold a hand on needs attention. Hot oil is thin, leaks past internal clearances and ages quickly, so move the pack away from the dryer or improve air flow around it.
Where should the power pack stand on a coating machine?
The power pack should stand in cool, clean air, away from the dryer body, burners and hot ducts, and clear of splashes from the coating station. The supplied oil and air pipes are 5 metres long, which gives room to place the tank at the unwind end or operator side while the cylinder sits at the guide.
Can an air sensor be used near a solvent based coating head?
An air sensor is well suited to that position, because the sensor head and its pipe carry only low pressure air and no electrical signal. The power pack motor is still electrical, so its location and fittings must follow the rules for the area. State the area classification in the enquiry.
Does the web guide control coating weight or coating width?
No. The web guide controls only the sideways position of the web. Coating weight and coated width are set at the coating head. What the guide does is keep the coated band in the same place on the web, so the margins stay even and the full coated width is usable after slitting.
